Coaxial Cable Products for Civil Aviation From HF through Ka band, TMS has the right solution for civil aviation communications, collision avoidance, navigation, remote sensing and in-flight entertainment.Catalog Handbook
High Power Times offers a broad range of cables, connectors and assemblies for high power RF transmission, including magnetic resonance imaging (MRI), semiconductor manufacturing equipment, broadcast and high power laser applications.Catalog Handbook
Interpretation of electrical test data Technical
Zero dB™ Cable Assemblies Picture this, you have an antenna located at the tip of the
aircraft’s wing. This gives you the best field of view, but
makes the cable runs very, very long. The receiver is located
forward in the avionics bay where power, cooling air, and maintenance
access are all necessities. This means you’ll have a very long
cable run.Technical
The Wireless Internet Connection Cable considerations for today's systems.Technical
Protect Your Network System designers should keep these parameters in mind when choosing lightning and grounding equipment for communications sites.Technical
Pin Height The importance and role of RF coaxial connector pin height and its impact on electrical and mechanical performance.Technical
Phase Track® Cable - TF4™ Dielectric: The “Knee Replacement” In our continuing pursuit for excellence, Times Microwave Systems has developed the Phase Track® line of phase stable, low loss cable products. These products are designed for use on many application platforms but are particularly well suited for thermal vacuum test and space flight cable requirements.Technical
Optimizing Microwave Signal Transmissions In Extreme Cryogenic Environments This paper describes the rational for choosing the optimum cable for use in cryo cooled amplifier applications. It applies to the general case where it is important to maximize signal transmission while minimizing heat loading on the cryo-cooled environment.Technical
Optimizing and RF Transmission Line Obtaining efficient antenna feeder and jumper assemblies requires attention to the connector as well as the cable.Technical
On Site Testing of Lightning Protection Devices The Times Protect LP-SPT Surge Protection
Tester is designed to test all coaxial cable RF
Lightning Protection products offered by Times
Microwave. Other LP products based on
transient protection devices such as GDT,
MOVS, TVS and SIDACs and mechanical
filter designs can be tested. Moreover the LPSPT
is suitable for testing discrete transient
devices as well.Technical
Current Innovations In Phase Stable Coaxial Cable Design The development of a new Dielectric material, TF4™, now gives the system designer a previously unavailable option with far better phase performance than PTFE, Si02 or other conventional cables. For many applications, this is critical to achieving required system performance.Technical
Connector Torque Requirements In the world of RF coaxial threaded connections, too often the efforts of selecting a suitable connector interface, procuring it from a reliable source and manufacturing a high-quality assembly are done in vain because the connector has not been tightened to the proper torque value and/or steps were not taken to ensure that the connection will be maintained during its application.Technical
Microwave Transmission Line Considerations for Vehicle Applications Whether on land, sea, or air, RF transmission lines installed in mobile platforms must be able to operate in severe conditions, including wide temperature and altitude ranges and high vibration exposures. They must be made using materials suitable for use in these demanding environments, and for reasons of safety, must not support flame or emit toxic vapors when burned.Technical
Rail and Transit Solutions TMS has consistently developed new products, innovations and qualifications across the Rail & Transit markets , whilst
having by far the most comprehensive range of cable / connector products in the industry.Catalog Handbook
Wireless Product Catalog This catalog contains information on LMR Cable Family, TCOM, Installation Tools and Hardware Accessories, T-RAD, SilverLine, IntraFlex, LMR-SW, SPP, SPO, SPF, TFT, TFT-LF, Bundled Cable, Times-Protect, and more.Catalog Handbook
Zero dB™ Coaxial Cable Assemblies for High Performance Aircraft Times Microwave Systems has recently
developed an integrated LNA package
to allow the location of a low-noise amplifier
(LNA) at the antenna, ahead of the cable
assembly, in high-performance aircraft.Technical
Lightning and Grounding Protection Times-Protect® Lightning and Grounding Protection for Wireless NetworksCatalog Handbook
WSB Weather Seal Boots Weather seal, strain relief boots for LMR-195 - 200, LMR-240, LMR-400 & LMR-600
DataSheet
Don’t Overlook the RF Connector Impedance uniformity across a cable assembly is paramount in the efficient transmission of RF energy. The cable assembly is
basically only as good as its weakest link. The time and money spent on high-quality, low-loss cable can be wasted if there are large impedance mismatches within the connectors, at the connector-cable interface, and at the connector-device interface.Technical
Complete Coaxial Cable Catalog and Handbook This catalog serves as a guide to many of the
products offered by Times and is a comprehensive
technical reference with useful technical information
on MIL-C-17 and RG cables.Catalog Handbook
A Novel Super-Robust Handgrip for Coaxial Connector Assemblies Times Microwave Systems has introduced a new and unique addition to its
popular SilverLine™ RF test cables. SilverLine-TG™ (TuffGrip™) is specifically designed to address the needs of cellular infrastructure, wireless Internet, and public mobile radio site installers and test technicians.Technical
How to Choose the Best Test Cable With so many choices, how does one decide on the appropriate test cables? Times Microwave introduces SilverLine Test cables, an all-around product designed for both production test and the lab, and priced to provide exceptional value.Technical
T-Rad and nu-Trac High Performance Radiating Cable Times Microwave Systems offers TRAD™ and NuTrac™ radiating
cables to provide RF coverage in structures which are otherwise
difficult to cover. Conventional examples include rail and
transit tunnels, underground mines, subways, metal-hulled ships,
offshore oil rigs, nuclear power plants and buildings with metal
supporting structures.Catalog Handbook
Coaxial Cable Assemblies Products and Capabilities TIMES MICROWAVE SYSTEMS is a technically oriented coaxial cable manufacturer that has been able to
continually meet and exceed the challenges for specialty engineered transmission lines for both the
commercial and military sectors.Catalog Handbook
In-building Cable Installations As the demand for wireless services increases, more antennas must be installed in less traditional installation environments, such as large buildings. The antenna feeder considerations are different in this type of environment.Technical
Making the Connection… With Coaxial Cable Cabling. It brings your system together like veins snaking through a human body. No place is this more true than in wireless data, whether it is for a wireless local-area-network, point-to-point or point-to-multipoint communications systems. These cables are a critical link, both as antenna feeders and jumpers.Technical
Times Microwave Systems Capabilities Brochure Times Microwave Systems, an Amphenol company designs and manufactures high
performance coaxial cables, connectors and cable assemblies for military, aerospace,
telecommunications and industrial RF and microwave applications. We are an engineering
organization committed to innovation and the development of new products for
demanding applications, as demonstrated by our record of accomplishment over our 60-
year history.Catalog Handbook
Microwave and RF Cable Assemblies: The Neglected System Component Part 1 Modern RF and microwave systems must perform at unprecedented levels of precision in harsh physical environments. These environments include extended immersion in deicing chemicals, hydraulic fluids, fuels, high altitudes, high vibration and wide-ranging temperature extremes.Technical
LMR 195, 240, 400, & 600 Coaxial Cables, Connectors, and Hardware Times LMR cables are high performance broadband,
flexible, low loss 50 Ohm coaxial communication
cables designed for use in wireless applicationsCatalog Handbook
Microwave and RF Cable Assemblies: The Neglected System Component Part 2 We’ve discussed some of the typical electrical characteristics of a cable assembly, and some of the environments typically encountered. Other aspects affecting the optimum design of a coaxial cable assembly are covered here.Technical
New Connector Field Installations Improve System Reliability Across the country, CDMA, TDMA, and GSM wireless communication sites are being upgraded to meet the requirements of the
FCC’s Enhanced 911, or E911, mandate. Phase II of this ruling requires that network-based wireless location systems locate a wireless phone user to within 100 meters 67 percent of the time, and to within 300 meters 95 percent of the time.Technical
On the Right Path Radiating cable provides tunnel communications for the World Trade Center PATH rail system project.Technical
Connecting Coaxial Cable Key to Radio System Deployment Among the keys to success in any wireless system are the quality and reliability of the connector installations on the coaxial cable transmission lines. And it naturally follows that the more difficult the connectors are to install, the lower the likelihood that they will be installed correctly thus adversely affection the quality and reliability of the entire system.Technical
LMR Ultra Flex <p>LMR® - UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles.</p>
<ul>
<li>Designed for outdoor use</li>
<li>Wide variety of connectors available</li>
<li>Available as pre-terminated assemblies</li>
</ul>DataSheet
SPO (Outdoor, Corrugated) <p>Super flexible, PIM rated, outdoor - SPO Jumpers are the ideal low PIM interconnect solution. </p>
<ul>
<li>-160 dBc PIM for optimal system performance</li>
<li>Corrugated copper outer conductor</li>
<li>Large selection of standard configurations </li>
</ul>DataSheet
SPF (Corrugated, Fire Retardant, 'Riser') <p>Fire retardant low loss, low PIM cable assemblies suitable for outdoor use.</p>
<ul>
<li class="MsoNoSpacing">UL listed, type CMR (riser) UL file #E-170516</li>
<li class="MsoNoSpacing">Super flexible</li>
<li class="MsoNoSpacing">Durable fire retardant, low smoke polyolefin outer jacket</li>
</ul>DataSheet
SPP (Plenum, Corrugated) <p class="MsoNoSpacing">Flexible, low PIM, plenum rated SPP jumpers are the ideal DAS interconnect solution.</p>
<ul>
<li class="MsoNoSpacing">-160 dBc PIM for optimal system performance</li>
<li class="MsoNoSpacing">UL listed, type CMP (plenum), UL file #E-170516</li>
<li class="MsoNoSpacing">Super flexible - designed for outdoor use</li>
</ul>DataSheet
TFT & TFT-LF <p class="MsoNoSpacing">Ultra flexible PIM and plenum rated jumpers that are the ideal DAS interconnect solution.</p>
<ul>
<li class="MsoNoSpacing">-160 dBc PIM for optimal system performance</li>
<li class="MsoNoSpacing">UL listed, type CMP (plenum), UL file #E-170516</li>
<li class="MsoNoSpacing">PIM, VSWR and insertion loss test results marked on each jumper</li>
</ul>
<p> </p>DataSheet
MilTech <p>Hermetically sealed flexible RF and microwave transmission line assemblies.</p>
<ul>
<li>Fully vapor sealed</li>
<li>Highly ruggedized</li>
<li>MIL-C-87104 & MIL-T-81490 qualified</li>
</ul>
<p class="MsoNoSpacing"> </p>DataSheet
M17 & RG <p>M17/RG Cables meet all MIL-C-17 requirements and provide good shielding effectiveness. They are low PIM, use standard connectors, and are readily available through distribution.</p>DataSheet
Military Shipboard <p>Military Shipboard Low Smoke Coaxial Cables are MIL-C -17 and MIL-DTL-17-QPL rated for MIL-Spec air frames, shipboard and ground applications. </p>DataSheet
High Power Assemblies <p>HP and HPL cables are suitable for the following applications:</p>
<ul>
<li>Semiconductor manufacturing</li>
<li>High power radars</li>
<li>High power lasers and many other applications</li>
</ul>DataSheet
MaxGain <p>Used for general applications in both field and laboratory conditions.</p>
<ul>
<li>Lowest insertion loss available – DC – 50 GHz</li>
<li>Ultra stable insertion loss and VSWR with flexing</li>
<li>Lighter weight compared to competing technologies</li>
</ul>DataSheet
SPO Assemblies <p>Super flexible, PIM rated, outdoor Jumpers.</p>
<ul>
<li>-160 dBc PIM for optimal system performance</li>
<li>Greater than 100 dB shielding</li>
<li>Polyethelene outer jacket – suitable for outdoor use</li>
</ul>DataSheet
SiO2 <p>Used in applications demanding the ultimate in phase tracking performance.</p>
<ul>
<li>Ultimate phase tracking performance</li>
<li>PTFE "knee" is non-exisitent</li>
<li>SiO2 dielectric technology</li>
</ul>DataSheet
High Power Assemblies <p>Times offers a broad range of cables, connectors and assemblies for high power transmission.</p>
<ul>
<li>Semi-conductor manufacturing equipment</li>
<li>High power lasers</li>
<li>Magnetic resonance imaging</li>
</ul>DataSheet
QEAM (Quick Erecting Antenna Mast) <p>Designed specifically for use in demanding, mission critical applications.</p>
<ul>
<li>Exceptionally low bending moment</li>
<li>Long bend life (typically more than 10,000 bends)</li>
<li>Fully weatherized</li>
</ul>DataSheet
PhaseTrack® <p>Used in applications demanding minimal phase change over temperature.</p>
<ul>
<li>Superior stability (vs LD PTFE)</li>
<li>PTFE "knee" is non-exisitant</li>
<li>TF4 dielectric technology</li>
</ul>DataSheet
PhaseTrack® SR <p>Classic semi-rigid-style cables with optimized phase performance.</p>
<ul>
<li>Superior stability (vs LD PTFE)</li>
<li>PTFE "knee" is nonexistant</li>
<li>TF4® dielectric technology</li>
</ul>DataSheet
PhaseTrack® PFlex <p>Flexible interconnect-style cables often used as a semi-rigid replacement.</p>
<ul>
<li>Superior stability (vs DL PTFE)</li>
<li>PTFE “knee” is non-existent</li>
<li>TF4 Dielectric technology</li>
</ul>DataSheet
LMR Bundled Cable <p class="MsoNoSpacing">LMR High quality low loss flexible cable bundled under a common outer jacket and used for multiple run applications.</p>
<ul>
<li>Fewer cable runs and ground kits</li>
<li>Reduced labor and material costs</li>
<li>Inner cables labeled with an identifier</li>
</ul>DataSheet
High Power (HP and HPL) <p class="MsoNormal"><span style="font-size: 10.5pt; font-family: Verdana, sans-serif;">HP and HPL cables are suitable for the following applications:</span></p>
<ul type="disc">
<li class="MsoNormal"><span style="font-size: 10.5pt; font-family: 'Verdana','sans-serif'; mso-fareast-font-family: 'Times New Roman';">Semiconductor manufacturing</span></li>
<li class="MsoNormal"><span style="font-size: 10.5pt; font-family: 'Verdana','sans-serif'; mso-fareast-font-family: 'Times New Roman';">High power radars</span></li>
<li class="MsoNormal"><span style="font-size: 10.5pt; font-family: 'Verdana','sans-serif'; mso-fareast-font-family: 'Times New Roman';">High power lasers and many other applications</span></li>
</ul>DataSheet
StripFlex II (SFT) <p>SFT™ high-performance microwave cables are rugged and flexible, making them ideal for interconect applications.</p>
<ul>
<li>Lower loss than SF versions</li>
<li>Superior shielding effectiveness </li>
<li>Low passive intermod (-155 dBc)</li>
</ul>DataSheet
Nu-Trac <p>Larger sized radiating cable</p>
<ul>
<li>Stable electrical performance</li>
<li>Flexible construction</li>
<li>No need for cable standoffs</li>
</ul>DataSheet
StripFlex (SF) <p class="MsoNoSpacing">StripFlex II cables provide the ultimate performance in a flexible cable.</p>
<ul>
<li class="MsoNoSpacing">Lower loss microwave interconnect</li>
<li class="MsoNoSpacing">Wireless base station interconnect</li>
<li class="MsoNoSpacing">Excellent connector selection</li>
</ul>
<p> </p>DataSheet
Coppersol & Coppersol CLL <p>Semirigid Coppersol coax features lower loss than flexible cables.</p>
<ul>
<li class="MsoNoSpacing">Lower loss than flexible cable</li>
<li>Superior shielding effectiveness</li>
<li class="MsoNoSpacing">Low passive intermod (PIM)</li>
</ul>DataSheet
Gas Tube Replacement Kits Gas tube replacement kit for the LP-GTR-N and LP-GTR-D product family.DataSheet
Universal Grounding Bracket Universal bulkhead-flange adaptor for mounting and grounding. One unit accommodates both DIN and N connectors.DataSheet
RF Lightning Protector Selection Guide <p>Use this selection guide to find the Times Protect product that fits your needs.</p>DataSheet
PhaseTrack® LS <p>Phase-Optimized Flexible Cable that is suitable for all phase sensitive systems.</p>
<ul>
<li>Ultimate phase tracking performance</li>
<li>PTFE “knee” is non-existent</li>
<li>SiO2 dielectric technology</li>
</ul>DataSheet
TFlex <p>Flexible Alternative to Semirigid Coax for Military and Commercial Applications.</p>
<ul>
<li>Meets all MIL-C-17 requirements</li>
<li>Excellent shielding effectiveness</li>
<li>Low passive intermod (PIM)</li>
</ul>DataSheet
HeliFoil (HF) <p>DC-18 GHz ultra low loss bulk coaxial cable and connectors for self assembly.</p>
<ul>
<li>DC-18 GHz do it yourself cable assemblies</li>
<li>Ultra stable insertion loss</li>
<li>Extremely flexible, low minimum bend radius</li>
</ul>DataSheet
SpaceFlight <p>Times Microwave Systems designs and manufactures the highest performance cable assemblies for space flight applications. </p>
<ul>
<li>Low loss</li>
<li>High power handling</li>
<li>Multipaction resistant - vented connectors</li>
</ul>DataSheet
MilTech® Light <p>MTL cables provide the same electrical performance as MilTech cables but with lighter weight.</p>
<ul>
<li>Lowest loss and superior phase tracking</li>
<li>Qualified for commercial, military and other demanding applications</li>
<li>Excellent electrical performance</li>
</ul>DataSheet
Field Deployable <p>Feeder cable for military field deployable antennas.</p>
<ul>
<li>Excellent electrical performance</li>
<li>Superior flexing</li>
<li>Resistant to harsh environments</li>
</ul>DataSheet
Multi-port Systems <p>Designed for high performance environments.</p>
<ul>
<li>Qualified to meet MIL-T-81490 and MIL-C-87104 specificatoins</li>
<li>Excellent shielding</li>
<li>Phase stability with low VSWR</li>
</ul>DataSheet
Microwave Cables <p>High-performance microwave cables are rugged and flexible, making them ideal for interconnect applications. </p>DataSheet
TVAC <p>Times Microwave Ststems provides a wide variety of customized cable assemblies for Thermal Vacuum Testing.</p>DataSheet
M17 & RG Cables <p>Special high performance cables with superior electrical and physical characteristics.</p>
<ul>
<li>Meets all MIL-C17 requirements</li>
<li>Good shielding effectiveness</li>
<li>Low passive intermod (PIM)</li>
</ul>DataSheet
LMR-DB-RR <p>LMR-DB-RR utilizes a non-hazardous, non-toxic additive which deters rodents and other pests from chewing and gnawing on cable jackets, that can lead to damage and eventual failure in RF systems.</p>
<ul>
<li>Non hazardous, non-toxic Rodent Resistant </li>
<li>Low-loss, excellent RF shielding</li>
<li>-40ºC to +85º operating range</li>
</ul>DataSheet
Times Protect Warranty DataSheet
TCA - Times Commercial Aviation <p>TCA cables feature low attenuation, light weight, high flexibility and durable contructions to perform in the most challenging aerospace environments.</p>DataSheet
Coaxial Cable Products for Civil Aviation <p>TCA cables feature low attenuation, light weight, high flexibility and durable contructions to perform in the most challenging aerospace environments. We pair these with custom designed connectors to minimize return loss and simplify installation.</p>
<ul>
<li>Low loss</li>
<li>Lightweight technology</li>
<li>Broad temperature range</li>
</ul>DataSheet
SilverLine ExtraFlex <p>SilverLine®-XF was designed for testing delicate components such as exposed RF circuits with edge launch connectors. </p>
<ul>
<li>Production test for small sized RF products</li>
<li>Edge launch testing</li>
<li>General purpose RF interconnects through 18 GHZ</li>
</ul>DataSheet
SilverLine-LPA (Low PIM adapters) <p>SilverLine®- LPA low PIM adapters exhibit exceptional PIM performance in any cellular or wireless frequency range. </p>
<ul>
<li>Cellular or wireless</li>
<li>Tower or in-building</li>
<li>production or laboratory</li>
</ul>DataSheet
SilverLine-VNA Flex Supreme (50 & 70 GHz) <p>SilverLine®-VNA Flex Supreme™ 50 & 70 GHz are extremely flexible, very high-frequency coax cable assemblies designed for Vector Network Analyzer use.</p>
<ul>
<li>5G</li>
<li>Inter-satellite, point-to-point & wireless HDMI</li>
<li>Targeting/tracking systems</li>
<li>Components & subsystem development</li>
</ul>DataSheet
SilverLine®-SF-LL <p>SilverLine®-LL is a low loss version of traditional SilverLine and SilverLine-SF is approximately 40% more flexible than traditional SilverLine.</p>
<ul>
<li>40% more flexible</li>
<li>30% lower loss (SilverLine-LL only)</li>
<li>Identical proven attachment method</li>
</ul>DataSheet
Clarity™ Series Test Cables <p>Clarity™ Series 18, 26.5, and 40 GHz Test Cables provide industry-leading performance and unparalleled value.</p>DataSheet
Thermal Vacuum TVAC TVACDataSheet
SilverLine <p>SilverLine® Test Cables are cost effective, durable, high performance cable assemblies designed for use in a broad range of test and interconnect applications.</p>
<ul>
<li>High volume, in-process production test</li>
<li>Incoming/final test inspection</li>
<li>RF test systems interconnects</li>
</ul>DataSheet
SilverLine-VNA (18, 26.5 and 40 GHz) <p>SilverLine®-VNA is a precision test cable with excellent loss, VSWR and phase/flexure stability.</p>
<ul>
<li>Vector network analyzer measurements</li>
<li>Laboratory use</li>
<li>Research and development</li>
</ul>DataSheet
SilverLine-VNA (110 GHz) <p>SilverLine®-VNA 110 GHz is an armored, extremely high frequency coax cable assembly designed for use where waveguide is impractical.</p>
<ul>
<li>Collision avoidance radar test</li>
<li>Point-to-point backhaul system test</li>
<li>Probe connections</li>
</ul>DataSheet
LP-BTR Series <ul>
<li>DC Blocked for Maximum Surge Protection</li>
<li>Multi-Strike Capability</li>
<li>Broadband Performance from 20MHz up to 1000MHz</li>
<li>Exceptional RF Characteristics</li>
</ul>DataSheet
LP-BTR-W Series <ul>
<li>IP67 Weatherized for Outdoor Use</li>
<li>DC blocked for maximum surge protection</li>
<li>Multi-Strike capacity</li>
<li>Exceptional RF characteristics</li>
</ul>DataSheet
LP-GPX-05-N Series <ul>
<li>Bidirectional filter based design</li>
<li>Outstanding IL/RL characteristics</li>
<li>DC blocked RF path for superior performance</li>
<li>Fully weatherized housing</li>
</ul>DataSheet
LP-STRH-N <ul>
<li>N Connectors</li>
<li>Excellent PIM Performance</li>
<li>Outstanding IL/RL Characteristics</li>
<li>DC Blocked for Superior Surge Performance</li>
<li>High Surge Current Rating</li>
<li>Broadband Multi-Strike Design</li>
<li>High Power Rated</li>
<li>Fully Weatherized Housing</li>
<li>Solid Brass Construction for Durability and Long Life</li>
</ul>DataSheet
LP-STRH-D <ul>
<li>DIN Connectors</li>
<li>All features of LP-STRH-N</li>
<li>Long Term Evolution (LTE) and 700 MHz Public Safety Applications</li>
</ul>DataSheet
LP-STRH-4.3-10 <ul>
<li>4.3-10 Connectors</li>
<li>All features of LP-STRH-N</li>
</ul>DataSheet
LP-STR-N <ul>
<li>N Connectors</li>
<li>Excellent PIM Performance</li>
<li>Outstanding IL/RL Characteristics</li>
<li>DC Blocked for Superior Surge Performance</li>
<li>High Surge Current Rating</li>
<li>Broadband Multi-Strike Design</li>
<li>High Power Rated</li>
<li>Fully Weatherized Housing</li>
<li>Solid Brass Construction for Durability and Long Life</li>
</ul>DataSheet
LP-STR-D <ul>
<li>DIN Connectors</li>
<li>All features of LP-STR-N</li>
</ul>DataSheet
LP-STRL-N <ul>
<li>N Connectors</li>
<li>Long Term Evolution (LTE) and 700 MHz Public Safety Applications</li>
<li>Excellent PIM Performance</li>
<li>Outstanding IL/RL Characteristics</li>
<li>DC Blocked for Superior Surge Performance</li>
<li>High Surge Current/Power Rated</li>
<li>Broadband Multi-Strike Design</li>
<li>Fully Weatherized Housing</li>
<li>Solid Brass Construction for Durability and Long Life</li>
</ul>DataSheet
LP-STRL-D <ul>
<li>DIN Connectors</li>
<li>All features of LP-STRL-N</li>
</ul>DataSheet
LP-GTV-N <ul>
<li>N Connector</li>
<li>DC Pass Multi-Strike Design</li>
<li>Broadband Bidirectional Design</li>
<li>Excellent IL/RL Performance Over the Entire Operating Frequency Band</li>
<li>Fully Weatherized Housing</li>
<li>White Bronze Plated for Durability and Long Life</li>
</ul>DataSheet
LP-GTV-S <ul>
<li>SMA connector</li>
<li>All features of LP-GTV-N</li>
</ul>DataSheet
LP-GTV-T <ul>
<li>TNC connector</li>
<li>All features of LP-GTV-N</li>
</ul>DataSheet
LP-HBX-N <ul>
<li>N Connectors</li>
<li>DC Blocked for Maximum Surge Protection</li>
<li>Multi-Strike Capability</li>
<li>Broadband Performance from 100MHz up to 700MHz</li>
<li>Exceptional RF Characteristics</li>
<li>High Power Design for Single & Multi Channel Applications</li>
</ul>DataSheet
LP-HBX-D <ul>
<li>DIN connectors</li>
<li>All features of LP-HBX-N</li>
<li>Universal Mounting/Grounding Bracket Included</li>
</ul>DataSheet
LP-SPT <ul>
<li>Can test any lightning protection device or component to ensure its proper functioning and capability to protect RF equipment</li>
<li>Completely portable (ideal for field use)</li>
<li>Two terminals (N male and N female)</li>
<li>Can test surge protectors with any other interfaces by using commonly available RF adaptors</li>
</ul>DataSheet
LP-DCX-W <ul>
<li><span style="color: #212529; font-family: 'Open Sans', sans-serif; font-size: 16px; background-color: #eeeeee;"> Ideally suited for protecting DC powered remote radio heads (RRH)</span></li>
<li><span style="color: #212529; font-family: 'Open Sans', sans-serif; font-size: 16px; background-color: #eeeeee;">Protects RRH and ground-based electronics</span></li>
<li><span style="color: #212529; font-family: 'Open Sans', sans-serif; font-size: 16px; background-color: #eeeeee;">Multi strike design is fully weatherized to IP-68</span></li>
<li><span style="color: #212529; font-family: 'Open Sans', sans-serif; font-size: 16px; background-color: #eeeeee;">Provides lowest surge energy and voltage throughput compared to any available alternate protective device</span></li>
</ul>DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated‘CMR’ and ‘FT4’ respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.DataSheet
LMR-DB is identical to standard LMR plus has the advantage of being watertight. The ddition of waterproofing compound in and around the foil/braid ensures continuous reliable service should the jacket be inadvertently damaged during installation or in the future.
DataSheet
Ideal for Medium antenna feeder runs (no jumpers required) Any application (e.g. WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
Ideal for� Medium antenna feeder runs - Jumper assemblies for 1-5/8" & 2-1/4" feeders - Building top sites - Any application (e.g. WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
Ideal for� Long antenna feeder runs - Building top sites - Any application (e.g. WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
Ideal for Jumper assemblies in wireless communications systems - short antenna feeder runs - Any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable - Drop in replacement for RG-58 and RG-12DataSheet
LMR- PVC is designed for low loss general-purpose
applications and is somewhat more flexible
than the standard polyethylene jacketed LMR.
DataSheet
LMR�- PVC is designed for low loss general-purpose
applications and is somewhat more flexible
than the standard polyethylene jacketed LMR.
DataSheet
LMR®- PVC is designed for low loss general-purpose
applications and is somewhat more flexible
than the standard polyethylene jacketed LMR.
DataSheet
LMR®- PVC is designed for low loss general-purpose
applications and is somewhat more flexible
than the standard polyethylene jacketed LMR.
DataSheet
LMR®- PVC is designed for low loss general-purpose
applications and is somewhat more flexible
than the standard polyethylene jacketed LMR.
DataSheet
Flexible low loss communications coax - drop in replacement for RG-316/RG-174 (uses standard connectors). Ideal for jumper assemblies in wireless communications systems and short antenna feeder runs.DataSheet
LMR- DB is identical to standard LMR plus has the advantage of being watertight. The ddition of waterproofing compound in and around the foil/braid
insures continuous reliable service should the jacket be
inadvertently damaged during installation or in the future.
DataSheet
LMR®- MA is a flexible cable designed specifically for mobile antenna applications. It has a PVC jacket and un-bonded aluminum tape to facilitate end stripping with automated equipment.DataSheet
LMR�- MA is a flexible cable designed specifically
for mobile antenna applications. It has a PVC jacket and
un-bonded aluminum tape to facilitate end stripping with
automated equipment.
DataSheet
LMR®- PVC is designed for low loss general-purpose
applications and is somewhat more flexible
than the standard polyethylene jacketed LMR.
DataSheet
LMR®- UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles. It is used for both indoor and outdoor applications. DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated ‘CMR’ and ‘FT4’ respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.DataSheet
LMR®- PVC-W is a white-jacketed version of LMR-
PVC for marine and other applications
where color compatibility is desired.
DataSheet
LMR®- PVC-W is a white-jacketed version of LMR-
PVC for marine and other applications
where color compatibility is desired. DataSheet
LMR®- PVC-W is a white-jacketed version of LMR-
PVC for marine and other applications
where color compatibility is desired.
DataSheet
LMR®- PVC-W is a white-jacketed version of LMR-
PVC for marine and other applications
where color compatibility is desired.
DataSheet
LMR®- PVC-W is a white-jacketed version of LMR-
PVC for marine and other applications
where color compatibility is desired.
DataSheet
LMR®- PVC-W is a white-jacketed version of LMR-
PVC for marine and other applications
where color compatibility is desired.
DataSheet
LMR®- PVC-W is a white-jacketed version of LMR-
PVC for marine and other applications
where color compatibility is desired.
DataSheet
LMR- MA is a flexible cable designed specifically
for mobile antenna applications. It has a PVC jacket and
un-bonded aluminum tape to facilitate end stripping with automated equipment.
DataSheet
LMR- DB is identical to standard LMR plus has the advantage of being watertight. The ddition of waterproofing compound in and around the foil/braid
insures continuous reliable service should the jacket be
inadvertently damaged during installation or in the future.
DataSheet
LMR- DB is identical to standard LMR plus has the advantage of being watertight. The ddition of waterproofing compound in and around the foil/braid
insures continuous reliable service should the jacket be
inadvertently damaged during installation or in the future.
DataSheet
LMR- DB is identical to standard LMR plus has the advantage of being watertight. The addition of waterproofing compound in and around the foil/braid insures continuous reliable service should the jacket be inadvertently damaged during installation or in the future.DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'T4'
respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4'
respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4' respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4'
respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4'
respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4'
respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4'
respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4'
respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4'
respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR is a non-halogen (non-toxic), low smoke,
fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-FR is UL/NEC & CSA rated 'CMR' and 'FT4' respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.
DataSheet
LMR®- FR-PVC is a general-purpose indoor cable
and has a UL/NEC & CSA rating of 'CMR' and 'FT4'
respectively. It is less expensive than LMR-FR, however
it emits toxic fumes (HCL) and greater smoke density
when burned.DataSheet
LMR®- FR-PVC is a general-purpose indoor cable
and has a UL/NEC & CSA rating of 'CMR' and 'FT4'
respectively. It is less expensive than LMR-FR, however
it emits toxic fumes (HCL) and greater smoke density
when burned.
DataSheet
LMR®- FR-PVC is a general-purpose indoor cable
and has a UL/NEC & CSA rating of 'CMR' and 'FT4'
respectively. It is less expensive than LMR-FR, however
it emits toxic fumes (HCL) and greater smoke density
when burned.
DataSheet
LMR®- FR-PVC is a general-purpose indoor cable
and has a UL/NEC & CSA rating of 'CMR' and 'FT4'
respectively. It is less expensive than LMR-FR, however
it emits toxic fumes (HCL) and greater smoke density
when burned.
DataSheet
LMR®- FR-PVC is a general-purpose indoor cable
and has a UL/NEC & CSA rating of 'CMR' and 'FT4'
respectively. It is less expensive than LMR-FR, however
it emits toxic fumes (HCL) and greater smoke density
when burned.
DataSheet
LMR®- FR-PVC is a general-purpose indoor cable
and has a UL/NEC & CSA rating of 'CMR' and 'FT4'
respectively. It is less expensive than LMR-FR, however
it emits toxic fumes (HCL) and greater smoke density
when burned.
DataSheet
Drop in replacement for RG-58 and RG-142. Flexible low loss communications coax - ideal for jumper assemblies in wireless communications systems - Short antenna feeder runs - any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
Ideal for� Jumper assemblies in wireless communications systems - short antenna feeder runs - Any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable - Drop in replacement for RG-58 and RG-12DataSheet
Ideal for Jumper assemblies in wireless communications systems - short antenna feeder runs - Any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
Ideal for Jumper assemblies in wireless communications systems - short antenna feeder runs - Any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable - Drop in replacement for RG-58 and RG-12DataSheet
LMR- DB is identical to standard LMR plus has the advantage of being watertight. The ddition of waterproofing compound in and around the foil/braid
insures continuous reliable service should the jacket be
inadvertently damaged during installation or in the future.
DataSheet
Ideal for drop-in replacement for RG-8/9913 air-dielectric type cable - Jumper assemblies in wireless communications systems - short antenna feeder runs - Any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
Ideal for� Jumper assemblies in wireless communications systems - short antenna feeder runs - Any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
LMR- DB is identical to standard LMR plus has the advantage of being watertight. The ddition of waterproofing compound in and around the foil/braid
insures continuous reliable service should the jacket be
inadvertently damaged during installation or in the future.
DataSheet
Ideal for® - Jumper assemblies in wireless communications systems - short antenna feeder runs - Any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
Ideal for drop-in replacement for RG-316/RG-174 - Jumper assemblies in wireless communiations systems - Short antenna feeder runs -Any application (e.g WLL, GPS, LMR, WLAN, WISP, WiMax, SCADA, mobile antennas) requiring an easily routed, low loss RF cable DataSheet
LMR-LW is a lightweight low loss coaxial cable that employs an aluminum braid shield instead of the traditional tinned copper shield. LMR-LW has been designed and engineered with a combination of electrical, physical and mechanical properties that reduce weight and cost.
DataSheet
LMR-LW is a lightweight low loss coaxial cable that employs an aluminum braid shield instead of the traditional tinned copper shield. LMR-LW has been
designed and engineered with a combination of electrical, physical and mechanical properties that reduce weight and cost.
DataSheet
LMR-LW is a lightweight low loss coaxial cable that employs an aluminum braid shield instead of the traditional tinned copper shield. LMR-LW has been designed and engineered with a combination of electrical, physical and mechanical properties that reduce weight and cost.
DataSheet
LMR-LW is a lightweight low loss coaxial cable that employs an aluminum braid shield instead of the traditional tinned copper shield. LMR-LW has been
designed and engineered with a combination of electrical, physical and mechanical properties that reduce weight and cost.
DataSheet
LMR-LW is a lightweight low loss coaxial cable that employs an aluminum braid shield instead of the traditional tinned copper shield. LMR-LW has been
designed and engineered with a combination of electrical, physical and mechanical properties that reduce weight and cost.
DataSheet
DataSheet
DataSheet
LMR®- UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles. It is used for both indoor and outdoor applications. DataSheet
LMR-200-UF LMR®- UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles. It is used for both indoor and outdoor applications. DataSheet
LMR®- UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles. It is used for both indoor and outdoor applications. DataSheet
LMR®- UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles. It is used for both indoor and outdoor applications. DataSheet
LMR®- UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles. It is used for both indoor and outdoor applications. DataSheet
LMR®- UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles. It is used for both indoor and outdoor applications. DataSheet
LMR®- UltraFlex has a stranded center conductor and rubber outer jacket designed for multiple bending/flexing cycles. It is used for both indoor and outdoor applications. DataSheet
LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75-FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-75-FR is UL/NEC & CSA rated 'CMR' and 'FT4' respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.DataSheet
LMR-75-FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. LMR-75-FR is UL/NEC & CSA rated 'CMR' and 'FT4' respectively, meets FAA FAR25 requirements and is MSHA-P for mining applications.DataSheet
LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75-DB is identical to standard LMR plus has the advantage of being watertight. LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75-DB is identical to standard LMR plus has the advantage of being watertight. LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75-DB is identical to standard LMR plus has the advantage of being watertight. LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75-DB is identical to standard LMR plus has the advantage of being watertight. LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR-75-DB is identical to standard LMR plus has the advantage of being watertight. LMR-75 standard is a UV Resistant Polyethylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any smooth wall or corrugated hard-line cables.DataSheet
LMR®- LLPX is an indoor highly fire retardant cable
intended specifically for runs within return air handling
plenums (e.g. dropped ceilings, raised floors). It has a
UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.
DataSheet
LMR® LLPL is an indoor highly fire retardant cable intended specifically for runs within return air handling plenums (e.g. dropped ceilings, raised floors). It has a UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.
DataSheet
LMR®- LLPL is an indoor highly fire retardant cable intended specifically for runs within return air handling plenums (e.g. dropped ceilings, raised floors). It has a UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.
DataSheet
LMR®- LLPL is an indoor highly fire retardant cable
intended specifically for runs within return air handling
plenums (e.g. dropped ceilings, raised floors). It has a
UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.
DataSheet
LMR®- LLPX is an indoor highly fire retardant cable
intended specifically for runs within return air handling
plenums (e.g. dropped ceilings, raised floors). It has a
UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.
DataSheet
LMR®- LLPX is an indoor highly fire retardant cable
intended specifically for runs within return air handling
plenums (e.g. dropped ceilings, raised floors). It has a
UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.
DataSheet
LMR®- LLPL is an indoor highly fire retardant cable
intended specifically for runs within return air handling
plenums (e.g. dropped ceilings, raised floors). It has a
UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.
DataSheet
LMR®- LLPX is an indoor highly fire retardant cable
intended specifically for runs within return air handling
plenums (e.g. dropped ceilings, raised floors). It has a
UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.DataSheet
LMR®- LLPX is an indoor highly fire retardant cable
intended specifically for runs within return air handling
plenums (e.g. dropped ceilings, raised floors). It has a
UL/NEC & CSA rating of 'CMP' and 'FT6' respectively.DataSheet
TCOM standard is a UV Resistant Polythylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.
DataSheet
TCOM PUR-DB is a UV Resistant Polythylene jacketed cable designed for 20-years service outdoor/watertight use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM PUR is a UV Resistant Polythylene jacketed cable designed for 20-years service indoor and outdoor use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM-FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. TCOM-FR has a UL/NEC & CSA rating of 'CMR' and 'FT4' respectively.DataSheet
TCOM standard is a UV Resistant Polythylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM standard is a UV Resistant Polythylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM PUR-DB is a UV Resistant Polythylene jacketed cable designed for 20-years service outdoor/watertight use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM PUR is a UV Resistant Polythylene jacketed cable designed for 20-years service indoor and outdoor use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM-FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. TCOM-FR has a UL/NEC & CSA rating of 'CMR' and 'FT4' respectively.DataSheet
TCOM standard is a UV Resistant Polythylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM PUR-DB is a UV Resistant Polythylene jacketed cable designed for 20-years service outdoor/watertight use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM-FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. TCOM-FR has a UL/NEC & CSA rating of 'CMR' and 'FT4' respectively.DataSheet
TCOM standard is a UV Resistant Polythylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
DataSheet
DataSheet
TCOM PUR-DB is a UV Resistant Polythylene jacketed cable designed for 20-years service outdoor/watertight use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM-FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. TCOM-FR has a UL/NEC & CSA rating of 'CMR' and 'FT4' respectively.DataSheet
TCOM standard is a UV Resistant Polythylene jacketed cable designed for 20-year service outdoor use. The bending and handling characteristics are significantly better than any air-dielectric and corrugated hard-line cables.DataSheet
TCOM-FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. TCOM-FR has a UL/NEC & CSA rating of 'CMR' and 'FT4' respectively.
DataSheet
TCOM-FR is a non-halogen (non-toxic), low smoke, fire retardant cable designed for in-building runs that can be routed anywhere except air handling plenums. TCOM-FR has a UL/NEC & CSA rating of 'CMR' and 'FT4' respectively.DataSheet
LMR-LW-DB is identical to LMR-LW plus has the advantage of being watertight. LMR-LW is a lightweight low loss coaxial cable that employs an aluminum braid shield instead of the traditional tinned copper shield. LMR-LW has been designed and engineered with a combination of electrical, physical and mechanical properties that reduce weight and cost.DataSheet
FBT is an indoor/outdoor highly fire retardant cable
intended specifically for runs within and between base
station cabinets. It is also applicable for return air handling
plenums (e.g., dropped ceilings, raised floors). It has a
UL/NEC rating of ‘CL2P’ for plenum applications.DataSheet
FBT is an indoor/outdoor highly fire retardant cable
intended specifically for runs within and between base
station cabinets. It is also applicable for return air handling
plenums (e.g., dropped ceilings, raised floors). It has a
UL/NEC rating of ‘CL2P’ for plenum applications.DataSheet
FBT is an indoor/outdoor highly fire retardant cable
intended specifically for runs within and between base
station cabinets. It is also applicable for return air handling
plenums (e.g., dropped ceilings, raised floors). It has a
UL/NEC rating of ‘CL2P’ for plenum applications.DataSheet
FBT is an indoor/outdoor highly fire retardant cable
intended specifically for runs within and between base
station cabinets. It is also applicable for return air handling
plenums (e.g., dropped ceilings, raised floors). It has a
UL/NEC rating of ‘CL2P’ for plenum applications.DataSheet
FBT is an indoor/outdoor highly fire retardant cable
intended specifically for runs within and between base
station cabinets. It is also applicable for return air handling
plenums (e.g., dropped ceilings, raised floors). It has a
UL/NEC rating of ‘CL2P’ for plenum applications.DataSheet
FBT is an indoor/outdoor highly fire retardant cable
intended specifically for runs within and between base
station cabinets. It is also applicable for return air handling
plenums (e.g., dropped ceilings, raised floors). It has a
UL/NEC rating of ‘CL2P’ for plenum applicationsDataSheet
FBT is an indoor/outdoor highly fire retardant cable
intended specifically for runs within and between base
station cabinets. It is also applicable for return air handling
plenums (e.g., dropped ceilings, raised floors). It has a
UL/NEC rating of ‘CL2P’ for plenum applications.DataSheet
